The inside edges of the bend are extended by using a straightedge and marking with a pencil. The point at which the lines intersect is where the ? is located.

Question: The inside edges of the bend are extended by using a straightedge and marking with a pencil. The point at which the lines intersect is where the ? is located. Select one: a. center of the bend b. first bend of an offset c. rise of the bend d. second bend of an offset … Read more

Perform the necessary calculations to pre-position the bends for the 30° offset in the photo. Calculate the position of Mark 1. (Distance to obstruction = 45 7/8″.) Note: The values calculated for this question will be used in additional questions.

Question: Perform the necessary calculations to pre-position the bends for the 30° offset in the photo. Calculate the position of Mark 1. (Distance to obstruction = 45 7/8″.) Note: The values calculated for this question will be used in additional questions. Click on the image to view a larger version of it. Select one: a. … Read more

Analyze the following table, and match the rise to the correct SHRINK.

Question: Analyze the following table, and match the rise to the correct SHRINK. Click on the image to view a larger version of it. 6 3/8″Answer 1Choose…1/16″1 3/16″5/8″1 7/8″1/2″ 5″Answer 2Choose…1/16″1 3/16″5/8″1 7/8″1/2″ 7/8″Answer 3Choose…1/16″1 3/16″5/8″1 7/8″1/2″ 2 1/2″Answer 4Choose…1/16″1 3/16″5/8″1 7/8″1/2″ 7 7/16″Answer 5Choose…1/16″1 3/16″5/8″1 7/8″1/2″ Answer: The Correct Answer is a. 1 3/16b. … Read more

Based upon the position of Mark 1 and Mark 2 for Conduit A, and the adjustment value calculated, calculate the position of Mark 1 for Conduit C. Note: The values calculated for this question will be used in additional questions.

Question: Based upon the position of Mark 1 and Mark 2 for Conduit A, and the adjustment value calculated, calculate the position of Mark 1 for Conduit C. Note: The values calculated for this question will be used in additional questions. Click on the image to view a larger version of it. Select one: a. … Read more

Based upon the position of Mark 1 and Mark 2 for Conduit A, and the adjustment value calculated, calculate the position of Mark 2 for Conduit B. Note: The values calculated for this question will be used in additional questions.

Question: Based upon the position of Mark 1 and Mark 2 for Conduit A, and the adjustment value calculated, calculate the position of Mark 2 for Conduit B. Note: The values calculated for this question will be used in additional questions. Click on the image to view a larger version of it. Select one: a. … Read more

The measured rise method for bending an offset should be used when the angle of the bend cannot be predicted or measured accurately.

Question: The measured rise method for bending an offset should be used when the angle of the bend cannot be predicted or measured accurately. Select one: True False Answer: The Correct Answer is TRUE Reason Explained The correct is TRUE Alex Timmonsrandnyevg34.com/

Since Conduit A is nearest to the obstruction, it will be used as the reference conduit and its layout done first. Calculate the distance from the end of the conduit to Mark 1 for Conduit A. Note: The values calculated for this question will be used in additional questions.

Question: Since Conduit A is nearest to the obstruction, it will be used as the reference conduit and its layout done first. Calculate the distance from the end of the conduit to Mark 1 for Conduit A. Note: The values calculated for this question will be used in additional questions. Click on the image to … Read more

Based upon the position of Mark 1 and Mark 2 for Conduit A, and the adjustment value calculated, calculate the position of Mark 2 for Conduit C.

Question: Based upon the position of Mark 1 and Mark 2 for Conduit A, and the adjustment value calculated, calculate the position of Mark 2 for Conduit C. Click on the image to view a larger version of it. Select one: a. 12″ b. 15 1/4″ c. 17 1/16″ d. 18″ Answer: The Correct Answer … Read more